Pinouts >  Genuine Mitsubishi Car audio Head Units  >  Mitsubishi pinouts

17 pin Audio Connector

Terminal No. Signal symbol Check condition Terminal voltage
2 SPEAKER RL (-) When the sound is output 0 - System voltage (AC)
3 SPEAKER FL (-) When the sound is output 0 - System voltage (AC)
6 AMP DATA Ignition switch: ON 0 - System voltage (DC)
7 SPEAKER FR (-) When the sound is output 0 - System voltage (AC)
8 SPEAKER RR (-) When the sound is output 0 - System voltage (AC)
9 MAIN GND Always 1 V or less
10 ILLUMINATION (+) Tail lamp switch: ON System voltage (DC)
11 SPEAKER RL (+) When the sound is output 0 - System voltage (AC)
12 SPEAKER FL (+) When the sound is output 0 - System voltage (AC)
13 VSS Ignition switch: ON 0 - System voltage (pulse)
14 ACCESSORY (+) Ignition switch: ACC position System voltage (DC)
15 SPEAKER FR (+) When the sound is output 0 - System voltage (AC)
16 SPEAKER RR (+) When the sound is output 0 - System voltage (AC)
17 BATTERY (+) Always System voltage (DC)

 

5 pin Connector

Terminal No. Signal symbol Check condition Terminal voltage
21 BATTERY (+) Always System voltage (DC)
24 PS-R Sift lever or selector lever : R position
Ignition switch: ON position
Hi : 5Mid : OpenLo : 0
25 GND Always 1 V or less

 

3 pin Rear Camera Connector

Terminal No. Signal symbol Check condition Terminal voltage
32 REAR SIGNAL When the image is output 1 Vp-p (AC)
33 SHIELD Always 1 V or less

 

7 pin Green Connector

Terminal No. Signal symbol Check condition Terminal voltage
101 ANTENNA POWER ON Ignition switch: ACC position System voltage (DC)
102 AMP POWER ON Ignition switch: ACC position 1 V or less
103 IE-BUS (+) Ignition switch: ACC position More than 120mV
104 IE-BUS (-) Ignition switch: ACC position More than 120mV

 

32 pin Handsfree Misc Connector

Terminal No. Signal symbol Check condition Terminal voltage
43 CAN-BOX DATA RX Ignition switch: ACC position 2 - System voltage(DC)
45 HFM SIGNAL (+) When the hands free system operation 1.2 Vrms (AC)
46 HFM SIGNAL (-) When the hands free system operation 1.2 Vrms (AC)
47 VIDEO2-IN When the image is input 1Vp-p (AC)
48 VIDEO2-R When the sound is input 1.2Vrms (AC)
49 SEIELD (VIDEO2-L/R) Always 1 V or less
53 AUDIO REMOTE Ignition switch: ACC position 3.3V (DC)
58 CAN-BOX DATA CLK Ignition switch: ACC position 1 - 5V (DC)
59 CAN-BOX DATA TX Ignition switch: ACC position 5V (DC)
61 HFM SIGNAL (+)-L When the hands free ECU or USB box operation 1.2 Vrms (AC)
63 SEIELD (VIDEO2-IN) Always Approximately 0 V
64 VIDEO2-L When the sound is input 1.2Vrms (AC)
65 VIDEO2 DETECT Always 1 V or less
69 SEIELD (STEERING REMO) Always 1 V or less

12 pin Camera Connector

Terminal No. Signal symbol Check condition Terminal voltage
81 VCC (RC 6.5v) Sift lever or selector lever : R position
Ignition switch: ON position
5.8 - 7.0V (DC)
82 GND Always -
83 CAMERA SIGNAL Sift lever or selector lever : R position
Ignition switch: ON position
1Vp-p (AC)
85 SHIELD (CAMERA) Always -
86 CAMERA DETECT Sift lever or selector lever : R position
Ignition switch: ON position
0 - 5V (DC)

 

There are no any reports for this pinout! You may rate this document by clicking the button below.

Is this pinout
Mitsubishi MMCS NR-261 NR-03 Head Unit visual pinout:
Mitsubishi MMCS NR-261 NR-03 Head Unit diagram
click to enlarge
Copyright © 2000-2019 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinoutguide.com .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.