Pinouts >  PDA, Tablet PC, MP3 players and other portable devices  >  PalmOne pinouts
16 pin PALM proprietary connector layout
16 pin PALM proprietary connector
Palm Universal connector
Pin Signal Description
1 GND Signal- and charge ground (connected to pin 7)   [ GPS Ground ]
2 USB_D+ Positive USB data signal [U1 green wire]
3 USB_D- Negative USB data signal [U2 white wire]
4 VBUS VBUS signal [U3 small red wire]
5 HOTSYNC HotSync IRQ - +3.3V for button push (via pin 9)
6 N/C Not Connected
7 GND Signal- and charge GND (connected to pin 1) [U4 small black wire]
8 ID

Identification for peripherials, resistor [R202=Zero Ohm] to ground. Should be short: USB cradle, 7.5 KOhm: Serial cradle, 20 KOhm: Mfg. Test Cradle, 47 KOhm: USB peripheral, 100 KOhm: Serial peripheral, 220 KOhm: modem

If pin 8 is shorted to ground, it forces USB mode. If left open, it forces Serial mode.

9 Vout +3.2V supply output, 100mA max.
10 RxD RS-232 RxD signal (input),  [GPS TX ] [D1]
11 TxD RS-232 TxD signal (output), [ GPS RX  ] [D2]
12 DETECT peripheral detect - tied to ground by peripherals [D3]
13 CTS RS-232 CTS signal (input) [D4]
14 RTS RS-232 RTS signal (output) [D5]
15 DTR RS-232 DTR signal (output) [D6]
16 CHARGE +5V charge supply input, 500-700mA



Palm USB cable:



 

Palm Universal connector (Tungsten T1, T2, T3, etc) has RS232 signals at RS-232 compatible levels, no voltage level translator from TTL to RS232 is needed. You can connect signals from your Palm Universal connect directly to PC or other compatible serial device.

PC-Palm synchronization cable pinout:

 



Connector board === PALM UNI  ===  PC DB9 Female
D2 ------- 11 (TxD) ------- 2 (RxD)
D1 ------- 10 (RxD) ------- 3 (TxD)
SH1/2 ----  1 (GND) ------- 5 (GND)
D6 ------- 15 (DTR) ------- 6 (DSR)
D4 ------- 13 (CTS) ------- 7 (RTS)
D5 ------- 14 (RTS) ------- 8 (CTS)
ID1 ------  8 (DEV-ID)             
E1/P1 ----  1 (PWR GND)            
E2/P2 ---- 16 (PWR V+)             

Pins 1, 7, and 12 should be shorted.  Pin 8 should be tied to the other three via a tiny 7.5k resistor or left open.  You may also want to bring out the two wires for the +5vdc charging connection, as well as tie pins 5 and 9 to a miniture push-button to initiate hot-sync.

 

Palm USB Cradle:  USB to Serial Mod:

This mod allows you to use your Palm device on Windows 7 computers by connecting it via a USB to Serial adapter, yet keeping it connected to power so that it stays charged.

 

Windows Vista users should check to see if 32 or 64 bit drivers are available, and if so, can follow the instructions outlined below to adapt the cradle to serial use.

 

Note: you may need to download 32/64 bit drivers from Prolific's web site, depending on the model of the USB - Serial adapter used.

 

OIther versions of Windows, (XP and earlier), support both the serial and USB drivers originally supplied by Palm with their devices, so no mod is necessary.

 

The Mod:

 

The Palm USB cradle for these devices contains a small PCB to which the universal connector is attached. It can be found by carefully removing the four small screws under the four feet using a #10 Torx bit and separating the top and bottom halves of the cradle.

One side of this PCB has connections for the USB cable labeled U1 - U6, ID1, P1, P2, SH1.

The other side of the connector, has unused solder points to connect a Serial cable labeled D1 - D6, E1, E2, SH2.

ID1 is not an actual part of the USB cable and has no connection.  The shorting connection for ID1 to enable USB mode is a small black device soldered just above the hot-sync switch.  To adapt the cradle to use a serial connection exclusively, the small black shorting device just above the hot-sync switch should be removed.

E1/P1 and E2/P2 are charging power connections located at each end of the cradle's connector board, connected using heavier wire to the Palm charger's barrel connector. SH1/SH2 are provisions for each cable's shield ground connection.  ID1 is the device identifier connection as noted above for Pin-8.

A USB cradle can be adapted to support both Serial and USB by adding an additional six conductor (with shield) cable, (and drilling a small hole in the back), wired to D1 - D6 on the connector board and a DB-9 (female) connector as noted on the diagram above.

A small switch or jumper block should be installed in the cradle's case and be soldered between ID1 (on the USB side of the PCB) and ground. After removing the tiny shorting device just above the HotSync switch, you can short the two pins (or throw the switch) to enable USB mode.  Opening the connection enables Serial mode.

 

4 pin USB A plug connector layout
4 pin USB A plug connector
According to 15 reports in our database (11 positive and 1 negative) the PalmOne Tungsten T3, T, T2, C, W, Zire 71, m125, m130, m500, m505, m515, i705 connector pinout should be correct.

Is this pinout
Source(s) of this and additional information: kolumbus.fi, http://www.pspilot.de/pppm505/pppm505.html
Copyright © 2000-2023 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinouts.ru .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.