|
S-Video to Composite video adapter specification users reports and reviews |
| Date | Content Revision |
User opinion | Comment | Approved by moderator? |
|---|---|---|---|---|
| CORRECT | APPROVED | |||
| CORRECT | trop of the ball ! | APPROVED | ||
| CORRECT | APPROVED | |||
| CORRECT | APPROVED | |||
| CORRECT | APPROVED | |||
| CORRECT | its ok | APPROVED | ||
| CORRECT | it worx great! | APPROVED | ||
| CORRECT | S-video male (output signal) TO rca-video (input jack) is correct. But, rca-video (as the output signal) to s-video input isnt working. Change the capacitor to 330pF (from tv-output-signal to pci-capture-card). Or 430pF (from handycam without firewire to pci-capture-card ). Warning: component value may vary. | APPROVED | ||
| CORRECT | I built it placing the capacitor before the RCA end and using one of 1nF (600-800 pF were also good) to get a more stable chrominance, but I probably had to use this greater value because the S-video input was from a notebook (Intel 82852 video card) | APPROVED | ||
| CORRECT | WORKS FINE . | APPROVED | ||
| CORRECT | WORKS FINE. | APPROVED | ||
| CORRECT | It is works on SECAM tv and I used 511 pF capicator. | APPROVED | ||
| CORRECT | Works fine but worth pointing out on pin diagram that the pin numbering is as viewed from the PIN side, not from the wiring side! | APPROVED | ||
| 2009-04-10 18:16:53 | rev. 3 | CORRECT | Capacitor is not nessesary | APPROVED |
| 2009-07-25 23:53:22 | rev. 3 | CORRECT | Works like a charm. Used a 560pF capacitor instead of the recommended 470pF and video quality was still fine. | APPROVED |
| 2009-10-24 18:02:19 | rev. 5 | CORRECT | APPROVED | |
| 2009-11-06 00:49:36 | rev. 5 | INCORRECT | Cap not nessasary did work but with unstable picture and lines. Cap seems to be the correct way | APPROVED |
| 2009-11-30 22:04:59 | rev. 5 | CORRECT | Excellent used without cap works great very helpful | APPROVED |
| 2010-01-31 06:25:51 | rev. 5 | CORRECT | This is very good no use of caps and works just take 4 and put as ground and 3 as signal and good to go. | APPROVED |
| 2010-11-18 16:40:56 | rev. 7 | CORRECT | 100% Correct | APPROVED |
| 2011-03-20 13:03:21 | rev. 7 | ERROR FIXED | Pins 3 and 4 should be shorted to RCA "Signal" Pin 1 - Ground | APPROVED |
| 2011-11-03 01:33:25 | rev. 7 | CORRECT | APPROVED | |
| 2012-01-05 15:30:29 | rev. 7 | CORRECT | APPROVED | |
| 2012-01-09 18:19:34 | rev. 7 | CORRECT | Thank's so much ! | APPROVED |
| 2012-01-29 09:29:33 | rev. 7 | CORRECT | APPROVED | |
| 2012-02-12 10:25:42 | rev. 7 | CORRECT | APPROVED | |
| 2012-06-15 21:42:16 | rev. 7 | CORRECT | APPROVED | |
| 2012-09-01 10:57:23 | rev. 7 | CORRECT | No errors at all. The circuit worked very well. Looked just as clean as using a normal S-Video cable. | APPROVED |
| 2012-10-05 08:11:55 | rev. 7 | CORRECT | this helped me alot | APPROVED |
| 2012-12-13 23:22:37 | rev. 7 | CORRECT | None... | APPROVED |
| 2017-01-07 22:07:52 | rev. 8 | CORRECT | No errors. Everything works well without the capacitor. Though I was initially having some issues with the color signals on a cheap mini DIN-4 connector, these issues were eliminated simply by using a higher-quality connector. | APPROVED |
| Date | Content Revision |
Author | Comment |
|---|---|---|---|
| 2008-10-21 21:21:59 | rev. 3 | Fabulous | For all of those who wanted the color coding there it is |
| 2009-10-19 22:19:41 | rev. 4 | Jeremy | no cap needed, connect pin 4 to ground, pin 3 to rca center pin, extra 2 wires (ground svideo arent used) |
| 2010-02-27 22:02:15 | rev. 6 | Dylan Lennox | |
| 2012-02-23 15:03:03 | rev. 7 | Jos van den Eijnden | |
| 2012-07-03 16:31:39 | rev. 7 | s-video to componnent | |
| 2014-03-12 13:12:11 | rev. 8 | I fixed a typing error. :) |
Pinouts.ru > Pinout of S-Video to Composite video adapter and layout of 4 pin mini-DIN male connector and 2 pin RCA plug connector |
should be correct |