Pinouts >  Распиновки последовательных портов
34 pin M/34 male connector layout
Разъем 34 pin M/34 male
Basically, V.35 is a high-speed serial interface designed to support both higher data rates and connectivity between DTEs or DCEs over digital lines.

V.35 is an interface (V.35 is the ITU - formerly CCITT standard termed "Data Transmission at 48 Kbps Using 60-108 KHz Group-Band Circuits") commonly used on higher speed circuits of 56kbps and above. Recognizable by its blocky, 34-pin connector; V.35 combines the bandwidth of several telephone circuits to provide the high-speed interface between a DTE or DCE and a CSU/DSU (Channel Service Unit/Data Service Unit). To achieve such high speeds and great distances, V.35 combines both balanced and unbalanced voltage signals on the same interface. Transmission is usually a synchronous protocol (note clocking pins i.e. receive and transmit clock). Although V.35 is commonly used to support speeds ranging anywhere from 48 to 64 Kbps, much higher rates are possible [ ISDN (64 or 128Kbps), Factional T1@ 128 Kbps to 1.544Mbps T1, ATM and Frame Relay]. V.35 cable distances theoretically can range up to 4000 feet (1200 m) at speeds up to 100 Kbps. Actual distances will depend on your equipment and the quality of the cable . Lan routers often come equipped with a V.35 electrical interface but many today are using a HSSI interface at speeds higher than T1 and above (typical T3 45Mbps).

Pin Name Dir Description
A ---Chassis Ground
B ---Signal Ground
CRTS-->Request To Send
DCTS&t;--Clear To Send
EDSR&t;--Data Set Ready
FDCD&t;--Data Carrier Detect
HDTR-->Data Terminal Ready
JLL&t;--Local Loopback
K -->Local Test
L  unused
M  unused
N  unused
PTxD--->Send Data A
RRxD-&t;--Receive Data A
STxD+-->Send Data B
TRxD+&t;--Receive Data B
U -->Terminal Timing A
V &t;--Receive Timing A
W -->Terminal Timing B
X &t;--Receive Timing B
Y &t;--Send Timing A
Z  unused
AA &t;--Send Timing B
BB  unused
CC  unused
DD  unused
EE  unused
FF  unused
HH  unused
JJ  unused
KK  unused
LL  unused
MM  unused
NN  unused

V.35 cable is balanced multipair with characteristic impedance 80-120 Om at the fundamental frequency.
Voltage is 0.55v+/-20% with 100 Ohm load.

There seem to be two versions of the V.35 pinning. One is called V.35 Winchester, the other is called V.35 Straight. One is mirrored to the other. We don"t know how it is mirrored. This information came from a 3Com source. Their Access Builder 4000 V.35 Card interface is V.35 Straight they say. The Dutch PTT supplies V.35 interface according to V.35 Winchester. Connecting these two requires some sort of crossed cable.

34 pin M/34 female connector layout
Разъем 34 pin M/34 female
На эту распиновку нет ни одного отзыва! Если вы знаете, правильная она или нет, - нажмите на соответствующую кнопку ниже.

Эта распиновка
Источник(и) этой и дополнительной информации: V.35 Page at Connectivity Knowledge Platform (Made IT)
Copyright © 2000-2024 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinouts.ru .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
Change privacy settings