Pinouts >  ATX, WTX and other standard and proprietary power supply (PSU) cables connectors
24 pin MiniFit Jr 5566-24 male (MOLEX 44206-0007) connector layout
24 pin MiniFit Jr 5566-24 male (MOLEX 44206-0007) connector
ATX 2.2 and later (ATX12V 2) is common ATX standard, 24 pin connector.

Changes to ATX standard were made to support 75 watt PCI Express requirements. Most power is now provided on 12 V rails and the power on 3.3 V and 5 V rails was significantly reduced. The standard specifies that two independent 12 V rails (12 V2 for the 4 pin connector and 12 V1 for everything else) with independent overcurrent protection are needed to meet the power requirements.

New ATX v 2.2 uses new connector, but most motherboards nowdays allow to use an old ATX v 1.x power supply with ATX 20 pin connector - it connects to 24 pin motherboard receptacle.

Pin Name Color
 
Description
1 3.3V Orange +3.3 VDC
2 3.3V Orange +3.3 VDC
3 COM Black Ground
4 5V Red +5 VDC
5 COM Black Ground
6 5V Red +5 VDC
7 COM Black Ground
8 PWR_OK Gray Power Ok is a status signal generated by the power supply to notify the computer that the DC operating voltages are within the ranges required for proper computer operation (+5 VDC when power is Ok)
9 5VSB Purple +5 VDC Standby Voltage (max 10mA, max 2A in ATX 2.2 spec)
10 12V Yellow +12 VDC
11 12V Yellow +12 VDC
12 3.3V Orange +3.3 VDC
13 3.3V Orange +3.3 VDC. ATX V2.3 / EPS12V V2.92 both define that the PSU has to use remote sensing to compensate cable drops on the 3.3V line. Because of this there is an additional brown cable crimped together with the orange cable either to pin 13 (ATX) or pin 1 (EPS12V).
14 -12V Blue -12 VDC
15 COM Black Ground
16 /PS_ON Green Power Supply On (active low). Short this pin to GND to switch power supply ON, disconnect from GND to switch OFF.
17 COM Black Ground
18 COM Black Ground
19 COM Black Ground
20 -5V White -5 VDC  (this is optional on newer ATX-2 supplies, it is for use with older AT class expansion cards and can be omitted on newer units)
21 +5V Red +5 VDC
22 +5V Red +5 VDC
23 +5V Red +5 VDC
24 COM Black Ground

 /PSON activated by pressing and releasing the power button while the power supply is in standby mode. Activating /PSON connects the power supply's /PSON input to ground, thereby switching the power supply to full-on condition.


 

18 AWG is recommended for all wires except pin 11, which should be 22 AWG. For 300W configurations 16 AWG is recommended.

24 pin MiniFit Jr 5557-24 female (MOLEX 39-01-2240) connector layout
24 pin MiniFit Jr 5557-24 female (MOLEX 39-01-2240) connector
According to 78 reports in our database (70 positive and 4 negative) the ATX 24 pin power supply connector pinout should be correct.

Is this pinout
ATX 24 pin power supply connector visual pinout:click to enlarge
Source(s) of this and additional information: ATX Spec v2.03 at Platform Development Support, from Hardware Book, http://www.formfactors.org/developer%5Cspecs%5CPSU_DG_rev_1_1.pdf Table 21, http://en.wikipedia.org/wiki/ATX, http://www.formfactors.org/developer/specs/ATX12V_PSDG_2_2_public_br2.pdf, None, http://www.formfactors.org/developer%5Cspecs%5Catx2_2.pdf
Copyright © 2000-2024 by pinouts.ru team, except user uploaded images.
No portion of this webpage may be reproduced in any form without visible link to pinouts.ru .
Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application.
Change privacy settings