various electronic devices and components not included in other sections.

Show device-specific * / 3Com / ADC / Adtran / ADVA / Alesis / Allen Bradley / Allied Telesyn / Arduino / ATEN / Avocent / AZ Instruments / Bayer / Baytech / Cellebrite / Cisco / Citizen / Comcom / Crypton / Danfoss / Dell / DeltaOhm / Device / Digi / DSC / Epson / Futaba / Heidenhain / HP / Imax / Intel / Inter-M / iRobot / LPC / LSC / Microchip / NetApp / Netbotz / Netscreen / Nortel / Olimex / Omron / Panasonic / Pico Allen / Planck / Rokenbok / Simatic / Telemann / Toa / Welch pinouts only (please note that filtering may not be accurate) or follow to 9 OLD hardware pinouts.
  • CCTV cameras DC iris connecor Manual iris CCTV cameras 4 pin iris setup connector
  • 6 pin RJ12 (6P6C) female connector drawing
    EasyPic 5..6 IDC Connector EasyPic5 or EAsyPic6 IDC Board Connection
  • 25 pin D-SUB female connector drawing25 pin D-SUB male connector drawing
    External POST controller LPT used for attachment of external LPT POST card to PCI POST controller
  • International Docking System Standard (IDSS) Power and Data Transfer Umbilical (PDTU) The International Docking System Standard (IDSS) is an international standard for spacecraft docking adapters.
  • 6 pin RJ12 (6P6C) female connector drawing
    OP-400 Automation Direct HMI Programing and Communications Connector 
  • SI Prefixes Table 
  • Terms and definitions 
  • TFT LCD module connector internal connectors of LP154WX4 TFT LCD and many others
  • 5 pin USB HDD case proprietary connector drawing4 pin USB A receptacle connector drawing
    USB 2.0 Disk connector cable Cable wiring diagram for USB cables used on some portable HDD cases.

3Com Pinouts

ADC Pinouts

Adtran Pinouts

ADVA Pinouts

Alesis Pinouts

Allen Bradley Pinouts

Allied Telesyn Pinouts

Arduino Pinouts

  • Arduino Esplora The Esplora differs from all preceding Arduino boards in that it provides a number of built-in, ready-to-use set of onboard sensors for interaction. It's designed for people who want to get up and running with Arduino without having to learn about the electronics first.
  • Arduino Ethernet The Arduino Ethernet is a microcontroller board based on the ATmega328. The Ethernet differs from other boards in that it does not have an onboard USB-to-serial driver chip, but has a Wiznet Ethernet interface. This is the same interface found on the Ethernet shield.
  • Arduino FIO The Arduino Fio is intended for wireless applications. The user can upload sketches with an a FTDI cable or Sparkfun breakout board.
  • Arduino Fishino UNO Fishino UNO is based on Arduino platform
  • Arduino Micro The Arduino Micro is a microcontroller board based on the ATmega32u4, developed in conjunction with Adafruit.
  • Arduino Mini The Arduino Mini is a small microcontroller board originally based on the ATmega168, but now supplied with the 328, intended for use on breadboards and when space is at a premium. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 8 analog inputs, and a 16 MHz crystal oscillator. It can be programmed with the USB Serial adapter or other USB or RS232 to TTL serial adapter.

ATEN Pinouts

Avocent Pinouts

AZ Instruments Pinouts

Bayer Pinouts

Baytech Pinouts

Cellebrite Pinouts

Cisco Pinouts

Citizen Pinouts

Comcom Pinouts

Crypton Pinouts

Danfoss Pinouts

Dell Pinouts

DeltaOhm Pinouts

Device Pinouts

Digi Pinouts

DSC Pinouts

Epson Pinouts

Futaba Pinouts

Heidenhain Pinouts

  • 15 pin D-SUB female connector drawing15 pin highdensity D-SUB male connector drawing
    Heidenhain TNC 407 / 415 / 425 LCD connection used to connect LCD monitor to Heidenhain TNC 407 / 415 / 425 at the pole X43 in replacement of old Screen VDU (BC 110) You can and should connect all GND together i both ends. The shield for RGB could also be connected but I have not tried yet to do that.

HP Pinouts

Imax Pinouts

Intel Pinouts

Inter-M Pinouts

iRobot Pinouts

  • 7 pin mini-DIN female (key in the center) connector drawing
    iRobot Roomba Open Interface (OI)  The Roomba Open Interface (OI) is a software interface for controlling and manipulating Roomba?s behavior. The software interface lets you manipulate Roomba?s behavior and read its sensors through a series of commands, including mode commands, actuator commands, song commands, and sensor commands that you send to the Roomba?s serial port by way of a PC or microcontroller that is connected to the Mini-DIN connector.

LPC Pinouts

LSC Pinouts

Microchip Pinouts

NetApp Pinouts

Netbotz Pinouts

Netscreen Pinouts

Nortel Pinouts

Olimex Pinouts

  • 10 pin IDC keyed male connector drawing
    Universal EXTension (UEXT) connector This connector includes power and three serial buses: Asynchronous, I2C, and SPI. The connector layout was specified by Olimex Ltd and declared an open-project.

Omron Pinouts

  • 10 pin Alcatel E801 cell phone proprietary connector drawing9 pin D-SUB female connector drawing
    Omron PLC to RS-232 calbe Omron PLC's Periherial connector to PC RS-232 cable Offical cable names: CQM1-CIF02 or CS1W-CN226

Panasonic Pinouts

Pico Allen Pinouts

Planck Pinouts

Rokenbok Pinouts

Simatic Pinouts

Telemann Pinouts

Toa Pinouts

Welch Pinouts


 
Copyright © 2000-2024 by pinouts.ru team.
No portion of this webpage may be reproduced in any form without providing visible HTML link to PinoutGuide.com
Change privacy settings